Assembling spiral chutes

Assembly of spiral chutes 1. Explanation of the chute selection process including inclined surface flow selection. The slurry is fed to a inclined chute or slope, and under the assistance of water, the mineral particle group is loose and layered. The light minerals in the upper layer are quickly discharged from the groove, while the heavy mineral materials in the lower layer stay in the groove or are discharged from the bottom at low speed. After each is connected, fine beneficiation or tailings can be obtained. Spiral chutes are equipment for mining and beneficiation, especially ideal for sand mining along coasts, rivers, sandbanks, and streams. The product has the characteristics of appropriate structure, easy installation, small footprint, easy operation, stable beneficiation, clear mineral separation, high yield, high efficiency beneficiation enrichment ratio, high recovery rate, and reliable operation. It has the advantages of small weight, moisture-proof, rust proof, not easy to corrode, and strong applicability to the fluctuation of feed volume, density, Granularity, and grade. 2、 Use the method to erect the spiral chute, calibrate the vertical line, fix the iron frame or wood in the proper position, and let the mineral sand be sent to the two ore feeding ports above the spiral by the mortar pump, participate in water filling, adjust the density of the mineral sand slurry, and the mineral slurry naturally swirls from top to bottom, generating a single coherent centrifugal force in the rotating slope flow speed, which is distinguished by the specific gravity, Granularity and state of the placer, By separating the ore and sand through the gravity of the swirling flow and the effect of this centrifugal force, the selected ore flows into the concentrate hopper and is piped out. The tailings are discharged into the tailings hopper and moved to the sand tank through a pipeline, and then discharged by a slurry pump, completing the entire beneficiation process. Assembled Spiral Chute III. Highlights and Features: 1. Ultra high efficiency, high recovery rate, and precise ore separation; 2. No power required; 3. Lightweight, rust resistant, wear-resistant, and corrosion-resistant; 4. Low operating cost and long service life; 5. Strong adaptability to fluctuations in ore feed volume, concentration, particle size, and grade; The friction force formed by the surface of 6 diamond sand makes the beneficiation effect superior to other plastic surfaces. Assembled spiral chute 4. Structural composition: The spiral concentrator consists of six parts: a feeding homogenizer, a feeding chute, a spiral groove, an equipment cutting groove, a product gathering hopper or groove bracket (including a cross or triangular frame), and so on. The main component is the rotating groove connected by the rotating disc. The spiral plate is made of fiberglass (fiber reinforced coal gangue) and is bolted together. The sorting surface of the spiral groove has a pre made wear-resistant layer. She has the advantages of lightweight, sturdy, and durable consumables. A multi tube feeding homogenizer is installed above the rotating groove to evenly sort minerals, making control simple and convenient. The mineral screening device is not limited to being placed on a cross (or tripod) on a supporting table. Uniform mineral mortar is slowly fed to the rotating groove surface through the feeding groove installed at the end of the spiral groove head, and selection is carried out. The tail end of the spiral groove is equipped with a valve block type new equipment to obtain the groove. The sorted new products are divided into three (or four) types of new products along the radial direction according to grade. Change the selection width of each new product by adjusting the orientation of the valve block. The new equipment gathering bucket is a concentric circular tube that allows the intercepted and variable mineral flows to be densely drawn out. The transverse section of the fiberglass chute and the slope change of the curve are extremely suitable for the selection of fine particle materials. 5、 Use This machine is suitable for sorting iron ore, ferrotitanium ore, chromite ore, pyrite ore, zircon ore, Rutile, monazite, phosphate ore, tungsten ore, tin, tantalum niobium, niobium with a particle size of 0.3-0.02mm and other non-ferrous metal ores, rare metals and non-metallic ore bodies with different density and specific gravity. Assembly of spiral chutes Assembly of spiral chutes